Three Phase Thyristor Power Controllers

Enquiry widget >West Control Solutions presents a range of thyristor power controllers which have been designed to switch 3 legs of 3 phase loads. These thyristor units are ideal for 3 phase configuration with neutral connection, normal (Relay S or Relay M) or variable resistive loads and transformer load types (PM3000-3PH).

Relay S- 3PH = Simple on/off firing with a DC logic input, time proportioned burst firing with a DC linear input (basic firing selectable between 4,8 or 16 cycles)

Relay M - 3PH = Time proportioned burst firing with a DC linear input (fully adjustable burst firing (3 to 255 cycles)), front panel display & keypad plus RS485 comms as standard

PMA3000 - 3PH = More complex load requirements that may need phase angle firing, delayed triggering, or features such as feedback, current limit etc.

Relay S - 3PH Thyristor Power Controller

Relay S - 3PH Thyristor Controller

Next Steps:

Ideal for:

  • Normal Resistance
  • Medium and Long Wave IR load types

Benefits & Features:

 

  • Integrated fuse + fuse holder is necessary to have a complete
  • power control zone including current transformer and optional circuit board
  • Flat Cable Wiring System (option) to connect in plug in mode many Revo S
  • when HB alarm or analog input are used
  • Input signal: SSR, Analog as an option
  • Zero Crossing, Burst Firing available at 4, 8 or 16 Cycles at 50%
  • of Power demand
  • Electronic fully isolated from power with constant current drain on input.
  • Heater Break alarm option to diagnose partial or total load failure
  • and Thyristor Short circuit
  • Fuse and Fuse holder available as an option
  • Current transformer integrated (with Heather Break option)
  • Special design for Heat sink with very high dissipation value
  • Comply with EMC, cUL (pending)
  • DIN RAIL side by side mounting
  • IP20 Protection

Specification:

  • Up to 500A

3, 4 or 6 wire

24Vac to 600Vac Supply

DC Logic input

4-20mA or 0-10V DC linear inputs

Zero Cross or Burst Firing (4, 8 or 16 cycles @50% power demand)

Relay M - 3PH Thyristor Power Controller

Relay M - 3PH Thyristor Controller

Next Steps:

Ideal for:

  • Normal Resistance
  • Medium & Long Wave IR and load types

Benefits & Features

  • RS485 Comms
  • MODBUS Protocol Standard
  • Frontal Key Pad to configure the unit and to read V,I and Power
  • Configurablity via RS485, USB Port and frontal Key Pad
  • Microprocessor based electronic circuit fully isolated from power
  • Universal input signal: RS485,Pot, Analog and SSR
  • Configurable Control Mode: V, I, V2 and VxI
  • Heather Break alarm to diagnose partial or total load failure and Thyristor Short circuit
  • Digital input configurable
  • Fuse and Fuse Holder Standard
  • Current transformer integrated in Fuse Holder
  • Comply with EMC, cUL pending
  • IP20 Protection
  • DIN RAIL mounting

Specification:

 

  • up to 500A
  • 3, 4 or 6 wire
  • 24Vac to 690Vac Supply
  • DC logic (SSR)
  • 4-20mA or 0-10V DC linear inputs
  • 10K Pot or RS485 Comms input
  • Zero Crossing
  • Burst Firing
 Powerstack 3PH Thyristor Power Controller

 

Next Steps:

Ideal for:

  • Most applications including Short Wave Infrared (SWIR) & Inductive load types

Benefits & Features:

 

  • Suitable to drive resistive, inductive, transformer with normal resistor
  • Two legs switching three wires loads STAR or DELTA connection
  • Frontal Key Pad standard to configure all the internal functions and
  • parameters.
  • Four Analog output configuirable
  • Six Digital input
  • Four realay output
  • Universal Input signal with automatic zero/span calibration.
  • Universal Firing modes, customer configurable via Key Pad or
  • communication port as Burst Firing or Delayed Triggering
  • Universal Feed back modes
  • Soft Start can be used in addition to Burst Firing and Phase Angle.
  • Unbalanced load and Heater Break Alarm.
  • RS 485 port. Modbus protocol
  • Comply with EMC
  • IP20 Protection

Specification: 

 

  • Up to 2700A
  • 3, 4 & 6 wire
  • 24Vac to 690Vac Supply
  • 4-20mA or 0-10V DC linear inputs
  • 10K Pot or RS485 Comms input
  • Burst Firing
  • Single Cycle
  • Soft Start + Burst Firing
  • Delayed Triggering + Burst Firing
  • Phase Angle
  • Soft Start + Phase Angle

 

PM3000-3PH Thyristor Power Controller

PM3000 3PH Thyristor Controller

Next Steps:

Ideal for: 

  • Most applications including Short Wave Infrared (SWIR) & Inductive load types

Benefits & Features: 

 

  • Suitable to drive resistive, inductive, transformer and complex loads
  • requiring current limit and power feedback.
  • Internal Key Pad to control the unit and to read power, current and
  • voltage value.
  • Universal Input signal with automatic zero/span calibration.
  • Universal Firing modes, customer configurable via Rs485 comm. as Burst Firing,
  • Single Cycle and Phase Angle.
  • Universal Control Mode.
  • Soft Start can be used in addition to Burst Firing.
  • Unbalanced load and Heater Break Alarm.
  • RS 485 port. Modbus protocol.
  • Internal fuses are standard on CD3000E-3PH
  • Comply with EMC, cUL (option)
  • IP20 Protection

Specification: 

 

  • 25A to 500A
  • 3, 4 or 6 wire
  • 330V to 600VAC Supply
  • DC Logic
  • 4-20mA
  • 0-10V DC linear
  • 10K pot or RS485 Comms input
  • Burst Firing
  • Single Cycle
  • Soft Start + Burst Firing
  • Delayed Triggering + Burst Firing
  • Phase Angle
  • Soft Start + Phase Angle